EVOLUTION 80 CAMSHAFTS
Andrews Products performance cams mean extra power for Evolution engines. H/D hydraulic lifters are capable of 6000+ RPM with stock springs and no valve float. Aluminum (T7) or chrome-moly pushrods (EZ-install type) are available to match any of our camshafts. Aluminum pushrods are lighter while the chrome-moly steel pushrods are more rigid for high performance.
EVOLUTION 80 TOURING AND PERFORMANCE CAMS     (See Evo Drag Cams @ Bottom of Page)
   TEC#  

Grind

   Duration   Valve Lift @            
Part# Timing(*) 0.053 0.020 Lift TDC Springs Application      
291117

84216

 EV31 10/46 236 270 0.495 0.133 STOCK Super power for supercharged engines; Basically an EV27 cam with timing set for superchargers or big inch motors with 10.5+ compression ratio.
  52/08 240 274 0.495 0.122  
             
291123

84217

 EV23 10/30 220 255 0.498 0.134 STOCK Mild bolt-in street cam with more torque and HP for all
  40/08 228 264 0.498 0.121   around riding with stock comp ratio. Similar to stock L
OK with fuel injectors or carburetors!   cam but more output. Pulls from 1800-5200 RPM.
291113

84218

 EV13 15/31 226 0.270 0.485 0.161 STOCK Bolt-in street/touring cam for heavy bikes. Much more
  45/13 238 0.280 0.495 0.148   low and mid-range power than either stock cam. Best
OK with fuel injectors or carburetors!   cam for 2 up riding with camping gear and side cars.
291127

84219

 EV27 20/36 236 270 0.495 0.182 STOCK A great bolt in cam for stock EV80 engines using state
  46/14 240 274 0.495

0.166

   of the art design. Very strong, broad torque band

 EV 27 Without Gear    TEC # 84241

   which will pull hard from 2000 to 5500 RPM.  
291130

84220    

EV3 21/37 238 280 0.495 0.197 STOCK Bolt-in street cam for light bikes (FXRS, etc.). Lots
  43/15 238 280 0.495 0.159   more mid-range and upper end power. Smooth idle

EV 3 Without Gear     TEC # 84242

   2800 to 6500 RPM cam with stock heads and springs.
291146 84221 EV46 25/41 246 283 0.495 0.207 STOCK Bolt-in performance cam; state of the art ramp design.
  49/17 246 283 0.495 0.163   Longer duration than EV3 but higher static comp. pressure; wide torque band; 2600 to 6000+ RPM.

EV 46 Without Gear     TEC # 84244

  
291151

84223

 EV51 28/44 252 286 0.510 0.233 STOCK Easy installation;  longer duration for modified street engines with hydraulic lifters and 9.0 or higher compression ratio. Power range from 2800-6500 RPM.
  54/22 256 290 0.510 0.195  

EV 51 Without Gear     TEC # 84246

  
291159 84228 EV59 28/48 256 290 0.560 0.236 HI-LIFT Upgraded EV57, fast ramps for modified 80 to 88 inch
  56/24 260 294 0.560 0.208   motors. Use with AP springs and collars. Very broad
              power band; 6000 RPM. OK for hydraulic lifters.
291172 84226 EV72 30/54 264 298 0.560 0.246 HI-LIFT Upgraded EV7, for 92 in. + street motors. For use with
    60/28 268 302 0.560 0.230   Andrews springs and titanium collars. Very broad
                power band, 2800-6000 RPM. OK for hydraulic lifters.
 
 EVOLUTION 80 PUSHRODS, SPRINGS and COLLARS

 

Evolution pushrods are available with EZ-install ends or standard adjustable tips. Both types are made in anodized aluminum or chrome moly steel. EZ-install pushrods can be installed without removing gas tanks or rocker boxes. If you are installing bolt-in cams, this is a big plus!   High Lift Springs for Evolution engines-used with titanium spring collars, cam lifts of .550+ can be accommodated. Installation does not require head machining.
Part# 294150 (4 inner and 4 outer springs)
TEC # Description Andrews
84283 High Lift Spring Kit  294150
TEC # Description Andrews Titanium upper spring collars will fit all Evolution 80 engines. Provides .050" more spring travel than stock collars. Collars are stronger and 50% lighter than stock collars.
84266 Standard Aluminum 292110
84268 Standard Chrome moly 292140
84252 EZ-install Aluminum 292215 84288 Titanium upper spring collars 293110
84253 EZ-install Chrome moly 292245
 
CAMS FOR DRAGS AND HIGH PERFORMANCE
For big engines (96+ cubic inches) or highly modified smaller motors and running compression ratios of 10.5 or higher, Andrews Products has high lift cams available which will put more usable power at the rear wheel than anything else going. These grinds are specially designed for highly modified motors.
 
  Installation requires expert knowledge and machining capability!